Magic: chops

Leave a comment

Owl chop

I recently read Benebell Wen’s brilliant book The Tao of Craft after hearing her on Gordon’s show.

One of the things that really caught my attention in the book was the idea that a Fu sigil or talisman should really be signed and sealed — that is, in the same way that a decree from the emperor would be signed and sealed, a Fu sigil carries the authority and mark of the creator. I explained this idea to my partner, who thought it was equally interesting. And so I decided to make a chop — a seal stick — for her, in part as practice for making my own. Which is part of the reason I made that captive ball a few days ago: I want to get better at wood carving, because it’s a useful skill to pair with woodworking generally, and because it will be a nice fit with the automata work I intend to do when the woodworking shop is up and functional again.

My partner frequently uses an owl as her emblem, so I went online and searched for how to carve an owl. This isn’t the one that I used, but it’s close enough — a series of photos of an owl carving.  I used basswood, because I don’t carve jade or soapstone (slightly different and sharper tools, more patience and care required); and I had the tools for this already. It’s a fairly simple procedure to carve an owl. It was also fairly simple to reverse and cut the runic-style emblem my partner uses for her magical sign, into the base of the chop. Except, I still screwed it up — and I’m going to have plane the bottom of her chop flat, and then cut it again.  I don’t have the tools out to do that yet, butI can certainly do something else while I wait to make that set of tools available.

img_3232From there, it was fairly simple to find a procedure for carving a bear. His advice about frequent sharpening is good — I sharpened my cutting tools about six times in the course of carving the bear, and I still wound up using too much force and chipping his right arm off.   I chose to do a statue against a pillar for my bear, because I want to have a place to practice chip carving, on the back of his pedestal; I already completed the small chip-carvings around the base, and I cut my own version of an emblem into the bottom of this seal.  I still think this won’t be my final seal, for me — the missing arm is a bummer.

So here we have an object that shares kinship with a magical-scribal-calligraphic tool from Chinese Taoist magic: a seal. But it’s carved in a Western style, with a Western character sign that indicates a person. And it could be used in western magic to do the same thing it does in Taoist magic: sign and authenticate and command the results in the name of the practitioner.

Is it cultural appropriation — Or cultural inspiration— to draw on the techniques and tools of other traditions to add to and build to the existing Western tradition? Ironically, I think this is part of the reason why I broke my bear at the last possible moment… because the character on the base of my chop is one I chose for myself from Chinese characters a decade or more ago.  But it’s not my emblem to use, nor my tradition. And so, this one is broken, and I’ll have to make it again.

But I still think it showcases what’s possible, what’s within the realm of workability.  The folk tradition of carving already exists in the West; the tradition of ‘enlivening’ statues and statuettes has been part of Western magic since Egypt; the idea of a personal seal to accompany a signature has fallen out of favor in the last two hundred years, but there are still signet rings in the Middle Ages, the Renaissance and early Enlightenment periods… and we have evidence of signets or seals all the way back into Babylon and Sumer, at least.

Maybe it’s time to re-awaken the idea of a personal seal.

Wood: captive ball

1 Comment

Stage two unlocked!

One of the basic exercises for woodcarvers is the creation of the Captive Ball, or Ball in a Cage.  Usually carved of a relatively soft wood like this basswood at first, then moving up to more complicated materials, the idea is to improve both knife and safety skills.

I only managed to get one small cut on the tip of my index finger while making this.  No bleeding — just a nip of the blade and a small pain.  When woodcarving, it’s difficult to aim the blade away from oneself the whole time; therefore the blade needs to be extra sharp so that you avoid trying to force it.  Chip Barton, the master woodcarver, explains in his book that you should sharpen your woodcarving tools at a fairly steep angle, first of all; and second that you should use a coarse stone, a fine stone, and then sandpaper mounted to paint stirrer-sticks at 800 grit, 1500 grit, 2000 grit, and 2500 grit if you can find it.  I made a set of sticks like that, and it was awe-inspiring how sharp I could get my blades; with practice, I’m sure I can get them even sharper.

Sharp tools are scary to some people, and I suppose with good reason. The assumption is that you’re at greater risk from a sharp tool, because it will cut deeper into the person holding it during an accident. But dull tools put one in the mindset that more force needs to be applied… and so there’s this Catch-22 (as in the novel by Joseph Heller) — a dull tool inspires its user to apply more force, which increases the likelihood that the tool will break or slip, and cause an injury; a sharp tool cuts more cleanly and carefully, and so less force needs to be applied… BUT, of course, the act of using a very sharp tool gradually dulls it. Which means that as the user gets tired, the tool is also getting ‘tired’, and the chances of an accident rises with the length of time one works with hand tools.

Fire-proud

Leave a comment

One candle in the dark: this was 2 days ago, the first day

I’m quite proud of this fire. It’s taken me most of the winter to learn how to do this, but I finally managed it.

I kept the wood stove burning for several days without over-filling it with wood every two hours. I didn’t have to get up in the middle of the night to fuel it. I just kept it burning by damping it and slowing, but not closing, its supply of oxygen. And in the morning, for several days now, behold: coals flaring to life.

It’s much more efficient to run a wood stove this way, apparently. And it makes the room where I do morning meditation much warmer and more comfortable. So I’m very excited. This is going to be a huge improvement on my effectiveness in the coming months, I think.

Cutting Mortises

2 Comments

This morning I cut mortises. I broke my last coping saw blade for wood while cutting dovetails last night, so i shifted over to work on a shelf for my reference books for woodworking — partly so all the books I have (and borrow) stay in one place, and partly so I don’t buy more books than I need (like that will stop me!).

Each shelf will be held in place by a pair of mortise and tenon joints. You can see in this first picture where I’ve drilled out the holes for the mortises. I wound up cutting six mortises today, much more cleanly and square than you see here.

mortise is a hole in a piece of wood, designed to be square (or at least the right shape to accept) to a matched tenon, or integral peg, in another piece of wood.  In furniture making, mortise and tenon joints are usually used in furniture intended to be collapsed for travel; it’s very common in medieval furniture where kings went on progress between manors, for example; and a lot of modern furniture built for the Society of Creative Anachronism (SCA) is similarly mortised and tenoned.  A secondary mortise is usually cut in the tenon, as well, to hold a wedge-shaped peg.  I plan to do that, too.

I had initially planned to cut all six mortises on each shelf upright, and the four on each of the three shelves, by hand.  But one took an hour, and so I drilled the other five out on one shelf with a powered drill press.  I plan to cut the other six mortises with not-just-a-drill-press but also a Forstner bit, to remove more of the waste material much more cleanly and faster.  The shelf panels are 3/4″ wide board which is nominally 1″x10″ (really 3/4″ x 9 1/2″-ish… even the 1/2″ isn’t accurate over the length of the board.)

The design of this bookshelf is pretty easy, really: it is three shelves with tenons— a tall shelf on the bottom for tradesman’s paperbacks and Popular Woodworking hardcovers; the middle shelf serves for hardcovers and trade paperbacks; and an open shelf on top for whatever happens to come my way. The three shelves are each half of a 6′-long board, and the verticals are also each a half of a 6′-long board.  The pegs in the tenons are going to be bits of 1″x 1″ square doweling cut and shaped to fit the holes; I may drill in screws or nails to hold bits of brass chain to hold the pegs, so the pegs don’t get separated from the uprights during transportation.  I plan to cut the tops of the uprights into a gothic arch, and maybe in the long run add some decorative carving — both to improve the look of a simple pine bookcase, and to reduce the overall weight of the parts.

I think my biggest challenge is going to be getting the mortises on the second upright cut so that the shelves lie mostly parallel to the floor and square.  Cutting the mortises in the shelf tenons will be relatively easy — I can drill out the waste and then use a chisel to make them mostly-square; the use of a peg there will help hold the shelf together, but so will the weight of the books on the shelf itself, as will the tension and pressure provided by the pegs.  I may have to add a secondary diagonal brace of some kind, but I have some ideas on how to do that; but most shelf designs like this don’t seem to need them — the three shelves themselves help keep things tight and square.

I did cut one end of one of the shelf boards with the tenons, and managed to fit them into the shelf mortises. They fit, but my tendency, I see, is to cut the mortises too wide and not high/tall enough.  I’ll have to correct this in future iterations.

Clamps

1 Comment

After I built the two tool-rack pegboards today, I built a six-pack beer caddy.  I didn’t have the right kind of wood in the plans for the beer caddy I found online, so I built it using some thinner wood I DID have.  The assembly was a bit nightmarish, as I was using 24″ and 36″ long bar clamps to keep the glued bits together during the assembly of the main ‘house-like’ part of the structure.  The thinner wood is nice, but I probably needed to cut a finger-hole or two in the horizontal board that acts as a handle.  I may drill a hole or two, anyway, and string a loop of cord or rope through it, to act as a handle.

That said, I’m not really confident in the strength and holding capacity of this design.  Too many things to go wrong, you see — glue failing, nails working free, boards splitting from water seeping into the wood from condensation on the bottles… a lot of things could go wrong. Should have overbuilt it with the 1/2″ wood instead of this flimsy stuff that I bought for another project. Should have built that other project, too — except, truthfully, that oak 1/4″ hobby board is nice stuff, and that other project was not turning out well.

More than that, I am not a big beer drinker.  Mostly, I don’t drink any beer.  But I did like the look of this caddy, and I have someone in mind to give this to as a gift.  It was simple to build, I had the materials and tools to do it, and I’m trying to use up my wood supplies enough that I don’t have to transport much raw lumber somewhere else before I move.

But back to clamps.

Clamps are an underrated tool in most MakerSpaces.  Everybody wants to spend money on the cool toys like the 3D printer and the milling machine and the laser cutter.  Everyone thinks about sawing and drilling and sanding, too.  But when it comes to assembly, most people think, “yeah, slap a bunch of glue on there, stick it together, and it’ll be fine.”

No. It won’t.

Most wood absorbs moisture like you wouldn’t believe.  It wants to warp and change. It does not want to stay flat and true; it wants to be round and it wants to transport water from the ground into the sky. It remembers being alive.  So when you add glue, which is moisture and stickiness, to wood — the wood sucks the moisture into its tubules, and then it bends in order to move that moisture from the wood end where it got the moisture, to somewhere in the middle.   And that moisture will warp the board.

Clamps help.  They allow the stickiness the time and opportunity to attach themselves one to another. They allow you the chance and opportunity to insert a few nails or a few screws to hold things together, and try to counteract some of that warping.  They’re not a perfect solution to anything.  But this simple four-board operation required at least three clamps at this stage.  And a little later on it needed six clamps… all of the largest clamps in my shop, in fact.

Now, multiply those six clamps by the number of people in your MakerSpace working on roughly similar projects — call it fifteen.  Six times 15 is ninety.  Ninety clamps.

I don’t have storage for ninety clamps, each 36″ long and 2-3″ wide.  You don’t either.  And more importantly, you don’t have room for ninety clamps deployed.  When I have just my six deployed, the room turns into a thicket of steel bars sticking out in every direction from the object being assembled.  Essentially, the object being assembled is now at the center of a cluster of steel or aluminum bars radiating out six feet from the center in three (call it two-and-a-half) directions.

So you can forego the clamps, because you just don’t have the space.  But then every one of those birdhouses is going to pop open and break at the earliest change in the weather.  You have to consider the role of clamping in the design of any assembly process, because clamping is a by-product of your decisions about glue.  More on that some other time.

Lucets

1 Comment

IMG_1086.jpgI made eleven lucets using my scroll-saw and some sandpaper. They turned out quite well.

They’re for sale on my new Etsy store, Watermountain Studios.

What can you use a lucet for? Making cord or braid, of course. That’s its primary purpose: to weave yarn into a strong cord or braid which resembles the mint family of plants: square stems.

I like braiding cord for various kinds of work that I do. Sometimes I sew it into tailoring projects to bulk out or decorate a seam; sometimes it becomes the handle for a bag or the drawstring for a pair of trousers.

Now you can make similar cord yourself.

Spoons

1 Comment


I carved two spoons today. The first had a long and spindly handle and I accidentally punched through the bowl of the spoon as I neared completion of it.

The second I was much more conservative with, and decided to leave off when it reached a state of “rustic but pleasing.”  The top spoon of course is the spindly one. The bottom one in the photo is the more conservative one.

Spoons are easier to carve than chip-carved panels. But they’re more of a high-wire act. The closer you get to “done” the more careful you must be. The closer you are to being “done”, though, the more risk you must take to get the curves smoothed out.

Older Entries